About Battery …
• Batteries should be stored in a closed, cool, and dry place without exposure to direct sunlight. Packaging standards and conditions must be followed in stacking. In storage, in accordance with the principle of “First In – First Out”, stock and shipment should be made according to the production dates.
Recharging is required when the open-circuit voltage of the battery falls below 12.4V with proper storage conditions. Generally,
• The need for recharging in Ca-Ca flooded batteries:
• Every 6 months if the average storage temperature is below 25 degrees (*)
• Every 3 months if the average storage temperature is above 25 degrees (*)
• For hybrid flooded batteries, these times are approximately 1 / It is up to 2.
While charging, electrolyte overflow and temperature should not be allowed to exceed 45 ° C. If the temperature rises, reduce the charging current or stop charging until the battery cools.
• Prepare the cable connections (if the cable ends are oxidized, they should be cleaned with hot water) and carefully examine the battery tray.
• Connect the Positive (+) cable first. Then connect the negative (-) ground wire. Make the mounting and pole connections of the new battery tightly according to the manufacturer’s instructions.
• Be especially careful when squeezing the battery terminals laterally, as over-tightening will damage the terminals. Since loose compression will cause explosions, the assembly should be done carefully according to the manufacturer’s instructions.
• Coat the terminals and cable end with an anti-corrosion agent.
The battery is equipment that stores electrical power in the form of chemical energy and gives it back in case of need. The task of the battery gives electric current to the starter motor for the first time to work, to send current to the receivers when the vehicle engine is not working. The other task of the battery provides a balance between voltage and amperage in the electric system when the engine operates and thus to prevent the receivers from damage as a result of high voltage that the alternator may generate at high speeds. In such cases, the battery takes over some of the current generated by the alternator and prevents overvoltage.
- Make sure that the battery you use for connection of one battery to another is of the same amperage.
- Switch off the engine and all electrical components.
- First, the red cable end is connected to the (+) terminal of the discharged battery; then the other end is connected to the terminal of the charged battery.
- And then the black cable end is connected to the terminal (-) of the charged battery and the other end of the cable is connected to any metal part of the vehicle having the discharged battery.
- Make sure the cables do not contact with any moving or hot things such as exhaust and impeller.
- And start the vehicle with the charged battery first, and then start the vehicle with the discharged battery.
- After the cars start, you may remove the jumper cables, starting with the vehicle with the discharged battery.
Possible reasons for discharge for GEP Batteries you bought:
- Adverse environmental and storage conditions, high temperature, humidity, etc.
- Leak currents on the car (currents drawn more than the anticipated short circuits), open lights
- Short circuits on other electric equipment and components
- Mismatch of the vehicle and battery; selection of small battery; additional onboard vehicle components (audio, light, computer systems, cooling systems)
- The insufficient charge generated by the alternator (charging generator)
Batteries have consisted of lead, sulfuric acid solution, and polypropylene box. For this reason, when batteries become unusable, they are risky and hazardous waste for the environment. However, an effective recycling system makes it possible to recover the polypropylene box and lead components of the batteries. Although it is also possible to recover sulfuric acid, it is mostly preferred to neutralize it.
Selection and Installation of Battery
Select the battery you desire properly according to the vehicle from the lists given in our catalog indicating characteristics of the batteries. Sizes, cold cranking current, and capacity values are important selection criteria. Activate the dry charged batteries according to the method given above and, if required, charge them.
In the case of flooded batteries stored, when the average daily temperature is less than 4°C, if the open-circuit voltage is 12.50 V and less, then recharge it according to the method given above.
If the ambient temperature is high and the open-circuit voltage is 12.40 or less, recharge it according to the method given above.
Mark the cables as +/- before you remove the old battery in order to connect the new battery correctly.
Measure the voltage value and direction of the battery to make sure it is correct; check the cable connections and battery stand carefully and clean them. Place the new battery and make the connections and tighten.
Firstly, connect the positive (+) cable. Secondly, connect the negative (-) earthed cable. Tighten carefully. As overtightening may damage the posts, be careful especially when you tighten the battery posts from sideways.
Cover the posts and cable ends by an anti-corrosive agent.